DMX / DALI / DMX Interface 4x is an advanced converter that allows to connect lighting installations based on the DALI protocol with DMX control systems.

This relay module is controlled via DMX512 and is used to switch on and off all kinds of loads in stage as well as architectural applications. The PX815 is manufactured in two versions: 2 channels with a maximum switching load of 16A/output or 3 channels with a maximum switching load of 13A/output.

This DMX/DALI converter is a development, which allows the combination of the two control systems in a simple way. With the PX787 you can connect devices that work with the DALI protocol to all controllers that send a DMX512 signal.

Demultiplexer DMX-512 signal on 0 – 10V. The PX227 is designed to process the DMX512 signal to control the eight analog 0 – 10V outputs with accuracy ±3%.

PX292 is used for processing DMX-512 signal to analog 4 – 20mA. In addition to DMX signal decoding, PX292 allows to program unit reaction to loss of DMX signal. Individually programmable parameters allow for independent definition of a DMX address from the range 1 – 512 for each channel.

Multiplexer is a device that allows to change analog signal 0 – 10V to the DMX512 signal. Analog signal is converted into a digital signal and then it is inserted or replaced at the appropriate (chose by the user) DMX channel from the DMX512 package.

PX796-IP, depending on the configuration, can be a transmitter or a receiver of a wireless DMX signal.
Wireless DMX is a device that allows you to connect easily, without using wires, installations based on the DMX512 control system.

With the DMX splitter the DMX input signal can be distributed to six independent lines. These are galvanically and optically isolated from the input as well as from each other. The splitter also serves to amplify the signal to each of the output lines. This supports the correct operation of the entire system. It is manufactured in a housing for mounting on a DIN35 rail.

PX257 is a device made in two versions: 8 Relay Module and Switch 8x1.3A OC. It is used for switching on and off stage lighting and theatrical effects as well as architectural lighting equipment using the DMX-512 signal. The module incorporates a set of 8 relays that control on / off outputs.

DMX Splitter is a universal splitter of the DMX signal. The device allows to create ramifications in the complex stage DMX installations and to amplify the DMX signal, that means, enables to connect next 32 receivers and to lengthen the DMX line. According to the
DMX standard, the receivers in a DMX route must be connected in series.

CT sensor is used to measure the color temperature in the range from 2500K to 6000K and the brightness. The measured value can then use the DMX-512 or RS-485 to send to other devices.

PX359 is a device to convert the DMX signal into the appropriate commands sent with the use of RS-232. The device is equipped with two independent buses RD-232, which various commands can be sent to. DMX – RS232 Interface is programmed with the use of the web interface without the need to install additional software and controllers.

The PX385 module is used to process DMX-512 signal to analogue control 0 - 10 V or 1 - 10 V with a relay (Relay Mode). The DMX/0-10 Interface 1ch has a DMX connector and 1 output voltage channel. PX385 can be controlled using a DMX signal (the device has a built-in DMX-512 signal receiver), and it can operate independently. The DMX address for the device is set manually using the DIP switch located on the housing, with the RDM protocol or using the PX277 configurator.

Universal splitter of the DMX signal. The device allows connecting additional 32 receivers and extends the DMX line.

Gate 4 DMX RDM device was created for 2-way converting Art-Net signal into four DMX512 and DMX512
ports on Art-Net.